2008/12/13 Wookey <wookey@wookware.org>

This just appeared on linux-embedded list. Very relevant to us. If
anyone has any comments about how it should work from balloon's POV
then now is the time to say.

----- Forwarded message from Florian Fainelli <florian@openwrt.org> -----

From: Florian Fainelli <florian@openwrt.org>
Date: Sat, 13 Dec 2008 13:58:01 +0100
To: Hugo Villeneuve <hugo@hugovil.com>
Cc: linux-kernel@vger.kernel.org, linux-embedded@vger.kernel.org
Subject: Re: FPGA programming driver architecture
List-ID: <linux-embedded.vger.kernel.org>
X-Spam-Status: No, score=-6.6 required=5.0 tests=BAYES_00,RCVD_IN_DNSWL_MED
autolearn=ham version=3.2.3, No

(CC'ing linux-embedded)

Salut Hugo,

Le Friday 12 December 2008 21:03:14 Hugo Villeneuve, vous avez écrit :
> Hi,
> I have written some code to program a FPGA in Linux, for two different
> types of boards: one uses a serial interface (SPI) and the second a
> parallel interface. I have been able to sucessfully program both boards.
> I'm now trying to clean my code and make it more generic, as well as better
> in line with the Linux driver model. I would also like to include it in the
> mainline kernel if there is interest.

Is it a platform-driver ? What do you provide in platform_data ?

>
> Here is a description of the current architecture (refer to diagrams
> below): The fpgaload module controls one output GPIOs (PROG), and two input
> GPIOs (INIT and DONE). These GPIOs are specified in board setup code. Both
> fpgaload_ser and fpgaload_par modules export a single function to write a
> byte. The fpgaload driver is a char device to which we can write
> (/dev/fpgaload) to program a bitstream (FPGA firmware) inside the FPGA.

You should probably consider using request_firmware to load the bitstream from
the userspace and possibly add a /sys interface to export some attributes
like :

- GPIOs being used between the host and the FPGA
- status (i.e : programmed, not programmed ...)
- FPGA vendor, type ...

> The
> fpgaload driver will toggle the GPIOs to initiate programming and the then
> call the corresponding write_byte function based on the interface type
> specified in board setup code (serial or parallel, or any future interface
> desired).

> The problem with that approach is that when loading the fpgaload module
> with modprobe, it will automatically try to load the fpgaload_ser and
> fpgaload_par modules, even if only serial interface was specified in board
> setup code for example. This is not good when building a kernel for similar
> but different boards.

What about something like that :

- fpgaload-core which contains all the code that can be shared between the
drivers like requesting firmware, providing sysfs attributes,
- fpgaload-spi would handle the low-level SPI connection
- fpgaload-par would handle the low-level parallel connection

fpgaload-ser and par would register with fpgaload-core and they could register
a fpga loading callback which is low-level specific for instance. Platform
code would instantiate the core driver. That way, adding support for other
loading protocols like slave serial or master serial can be done easily.

>
> Probably a better approach would be for the fpgaload_Ser and fpgaload_par
> modules to register themselves with the fpgaload module. Then, should the
> fpgaload module be built using a BUS driver structure? Or anyone having any
> suggestions on how it should be implemented?
--
Best regards, Florian Fainelli
Email : florian@openwrt.org
http://openwrt.org
-------------------------------
--
To unsubscribe from this list: send the line "unsubscribe linux-embedded" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html

----- End forwarded message -----
Wookey
--
Principal hats: Balloonz - Toby Churchill - Aleph One - Debian
http://wookware.org/

_______________________________________________
Balloon mailing list
Balloon@balloonboard.org
http://balloonboard.org/mailman/listinfo/balloon